ROCKINSUL BUILDING ROLLS
ROCKINSUL BUILDING ROLLS
ROCKINSUL Building Rolls is used mainly in pre-engineered buildings for roofs and walls to achieve excellent thermal and acoustic insulation. It can be used for both under purlin and over purlin application on the roof.
Stone wool fibers in ROCKINSUL Building Rolls are fine and uniformly distributed that ensures excellent & uniform thermal resistance. The stable stone wool fibers bonded with thermosetting resins are light in weight, strong and resilient.
ROCKINSUL BUILDING ROLLS
|Thickness(mm) Min and Max||Length(m)||Width(mm)|
|50 and 100||5 to 10||@1,100 (with overlap) to 1,200 (without overlap)|
|40 and 100||5 to 8|
* Non-standardized sizes and facing may be available on request
Click here to know more on standard product dimensions
ROCKINSUL RB Slabs are available unfaced or with facing of ALG, glass reinforced Aluminium Foil/ Kraft paper laminate facing (FSK), Black Fiber Glass Tissue (BGT)
Fiber : Up to 750 °C
Facing : 100 °C
At temperatures in excess of 230 °C a limited migration of binder may occur in the insulation in contact with the hot face. This does not impair the insulation performance.
ROCKINSUL RB Slabs achieve excellent acoustic performances (sound absorption coefficients, sound insulation, and impact sound isolation) when tested in accordance to various relevant ASTM standards. RB Slabs achieve Noise Reduction Coefficient (NRC) values up to 1, when tested in accordance to ASTM C423.
FIRE SAFETY PERFORMANCE
Unfaced ROCKINSUL RB Slabs are non-combustible when tested in accordance with IS 3144, BS 476 (part 4), ISO 1182 and ASTM E136 and are classified as Class A1, in accordance with European norms. Unfaced, FSK and ALG-faced RB Slabs have the following fire safety rating achievements:
- Class 1 surface spread of flame in accordance to BS 476 (part 7)
- Class 0 in accordance to the BS 476 (part 6 & 7) and to British Building Regulations.
- Surface burning characteristics in accordance to ASTM E84 / UL 723
- a: Fire Spread Index: Less than 25
- b: Smoke Developed Index: Less than 50
|Rockinsul and Tuffinsul exhibit excellent thermal insulation properties. The thermal performance of a product is indicated by R value and K value. R value is a measure of thermal resistance. Higher the R value, greater is the insulation efficiency.|
|An R-Value (thermal resistance) indicates the insulating power of an insulation material. The higher the R-value, the greater the insulating power i.e more energy savings.|
|As commonly defined, Noise is a sound that is loud or unpleasant or that causes disturbance. Sound is measured in a unit called the ‘decibel’ (dB). Our hearing range starts at 10 decibels (dB) and is considered safe up to 70 dB. Any prolonged exposure of sound of around 90 dB will lead to permanent damage to human ears. Extensive destruction and pain to the auditory nerves occurs at 140 dB. and destruction and|
persistent ringing in ears will occur immediately at 150-160 dB.
|There are two types noise control in buildings.|
|Reverberation time is the time taken for the sound pressure level to drop by 60 dB after the generated noise has been stopped.|
|Areas with a long reverberation time are referred to as being ‘live’, e.g. cathedrals and churches. Those with a short reverberation time are referred to as being ‘dead’, e.g. offices with thick carpets and absorbent ceilings.|
|A reduction of 60 dB in the sound pressure level is equivalent to the reduction of acoustic energy by a factor of one million. As a rough guide, the reverberation time of a room is approximately equal to the time it takes for loud clapping to become inaudible.|
|STC (Sound Transmission Class) value is a single number rating to specify the reduction in sound levels that the partition provides. The sound transmission loss performance of a partition is measured using ASTM E 90 “Standard Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements” and calculated according to ASTM E 413 “Classification for Rating Sound Insulation.” As a general rule, the higher the STC rating, the better the partition’s acoustical performance.|
|Ceiling Attenuation Class (CAC) ratings are used to determine the sound transmission loss through an acoustical or dropped ceiling. A CAC rating is determined by ASTM test method E 1414 “Standard Test Method for Airborne Sound Attenuation Between Rooms Sharing a Common Ceiling Plenum” and provides a value that is equivalent to an STC value|
|An IIC (Impact Isolation Class) rating describes the impact noise that is transmitted through a floor/ceiling assembly. The rating is determined by ASTM E 492 “Standard Test Method for Laboratory Measurement of Impact Sound transmission Through Floor-Ceiling Assemblies Using the Tapping Machine.” High ratings indicate that impact noise is reduced substantially.|
|Resilient channels are strips of metal with an offset that spaces the drywall approximately ½” away from the framing. They are typically installed 24 inches on center perpendicular to the studs. The use of resilient channels dramatically reduces the amount of sound that is conducted though the structure.|
|Q: Are there advantages to using steel studs over wood studs?|
Twenty five gauge steel studs provide superior sound control performance to wood studs with the same dimensions. The flexibility of the studs allows the partition to provide performance equivalent to a wood stud construction with resilient channels.
|Insulation for Building or for Industrial application will help to save energy when installed correctly; but selecting the right type of insulation material is very critical when it comes to fire safety and for insurance claim in case fire accident. Non combustible insulation products will prevent the spread of fire, reduce the emission toxic smoke and more importantly it will provide vital extra minutes to save lives and prosperities.|
|Rockinsul and Tuffinsul product are approved by globally recognized testing agency like FM, UL and Warrington for exhibiting higher fire rating.|
|All the products produced by us have always been free from gases that are harmful to the environment such as CFC’s, HCFC’s , HFC’s pentane or any gases. Rockinsul and Tuffinsul insulation products is one of few products that can save more than 100 times the energy used for its manufacture. It conserves scarce energy resources and reduces air pollution, CO2 emission and Sound pollution.|
|We can contribute towards sustaining this mother earth from any further irreversible damages. Power plants contribute to nearly half the world’s man-made Co2 output. In India 67% of the total electricity produced are from thermal plants. Over 65% of total install capacity are coal fires, 10% gas based and less than one percent other fuels. Power plants emit nearly 1kg of Co2 for kWh.|